BMW 3 of the E46 series

since 1998 release

Repair and operation of the car


BMW 3 of the E46 series
+ BMW 3 Cars (E46)
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply systems, injection and release
+ Electric equipment of the engine
+ RKPP and transmission line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   + Forward suspension bracket
   + Back suspension bracket
   - Steering with the hydraulic booster (servoupravleniye)
      Removal and installation of the block of a safety cushion on a steering wheel
      Removal and installation of a steering wheel
      Removal and installation of a tip of steering draft
      Removal and installation of steering draft
      Removal and installation of the pump of the hydraulic booster
      Filling with liquid and removal of air from a power steering hydraulic system
      Corners of installation of forward wheels. Check of installation of wheels
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment


Removal and installation of a tip of steering draft

Steering mechanism, covers and steering drafts

1 — steering draft right
2 — vrulevaya draft left
3 — a nut of M12, 65 N • m
Self-stopped, surely replace
4 — a set of covers of the steering mechanism right
5 — the steering mechanism
6 — a set of covers of the steering mechanism left
7 — a tip of steering draft
8 — a ring tightening

9 — a nut of tightening, 80 N • m
10 — a collar, Ø50 – 53 mm
11 — a ring basic
It is inserted into narrowing of steering draft near a six-sided nut. Before installation of steering draft grease it with jellied greasing at narrowing that at turn of draft to exclude joint rotation of a cover.
12 — a cover
13 — a collar, Ø65 – 68 mm


 REMOVAL

1 Mark paint the provision of a forward wheel concerning a nave. It will allow to establish the balanced wheel in the former situation. Weaken bolts of fastening of a wheel at the car standing on the earth. Lift forward part of the car and remove a wheel.

2 Measure the size - And - between the hinge and the end of a carving of steering draft
- 5-also write down the received value.

3 Weaken a tightening nut-1 tips of steering draft-2-, address to the Section Corners of installation of forward wheels. Check of installation of wheels.

4 Turn off a fastening nut-3 hinges of steering draft-4-. 2 – tip of steering draft.

5 Remove a tip of steering draft by means of the HAZET779 tool – 1.

6 Turn off a tip from steering draft, keeping thus draft a wrench for a hexagon-5-from a provorachivaniye.

At an otvorachivaniye count number of turns and write down the received value. It will facilitate further adjustment of forward wheels.


 INSTALLATION

7 Establish a tightening ring if it was removed on steering draft.
8 Screw a tip of steering draft, the number of turns has to be equal to number of turns at removal. Check the size - And - received before removal.
9 If it is necessary, clear of greasing a pin of the hinge of steering draft, and also an opening in a rotary fist.
10 Insert a tip of steering draft, and also an opening into a rotary fist. Screw the new self-stopped nut on a pin of the hinge and tighten its moment 65 N • m.
11 Tighten a tightening nut of a tip of steering draft the moment of 80 N • m. Thus keep draft from a provorachivaniye for a hexagon.
12 Establish into place a wheel so that the markings put at removal coincided. Previously grease with a thin layer of bearing greasing a wheel disk seat on a nave. Do not grease bolts of fastening of a wheel. Replace rusty bolts with the new. Fix a wheel bolts. Lower the car on wheels and tighten bolts cross-wise the moment of 100 N • m.
13 Check a track for HUNDRED, if necessary adjust.