BMW 3 of the E46 series

since 1998 release

Repair and operation of the car



BMW 3 of the E46 series
+ BMW 3 Cars (E46)
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply systems, injection and release
+ Electric equipment of the engine
+ RKPP and transmission line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures
   + Leaving and repair of damages of a body
   - External elements of a body
      Removal and installation of a front bumper
      Removal and installation/check of shock-absorbers of a bumper
      Removal and installation of a rear bumper
      Removal and installation of the back shock-absorber
      Removal and installation of a cover of a fairing
      Removal and installation of a forward wing
      Removal and installation of a cowl
      Adjustment of a cowl
      Removal and installation of a trunk lid
      Adjustment of a trunk lid
      Removal and installation of the lock/cylinder of the lock of a trunk lid
      Removal and installation of a gas-filled emphasis of a cowl/trunk lid
      Replacement of moldings and emblem of model
      Removal, installation and adjustment of a door
      Removal and installation of facing of a door
      Removal and installation of the lock of a door
      Removal and installation of the cylinder of the lock
      Removal and installation of the external handle of a door
      Removal, installation and adjustment of a window
      Removal and installation of the power window
      Removal and installation of the electric motor of a window regulator
      Removal and installation of a mirror of an external look / sound signal of a high-pitch tone
      Removal and installation of glass of a mirror
      Removal and installation of the case of a mirror of an exterior
   + Internal elements of a body
+ Onboard electric equipment
+ Schemes of electric equipment



Removal and installation of a forward wing

Observe instructions on carrying out body works, address to the Section the General information and security measures.


 REMOVAL

1 Disconnect a level on a wing by means of the wide plastic pallet.
2 Remove the lateral repeater of turn, address to the Section Replacement of Glow Lamps of External Lighting.
3 Remove a headlight, address to the Section Removal and installation of a headlight.
4 Remove upward protection of an edge.
5 Mark paint the provision of the corresponding forward wheel concerning a nave. It will allow to establish at assembly the balanced wheel in its former situation. Weaken bolts of fastening of a wheel at the car standing on the earth. Lift forward part of the car, put it on supports and remove a forward wheel.

6 Remove a loker of a wing at a longitudinal beam. For this purpose take out a small screw-driver clips-1-and-2-.

At first take out a pin from the center of a clip, and then take out a clip. The clip-2-on an illustration is closed by a level.

7 Turn off a nut-3-and a bolt-4-. Disconnect the lower cover of a motive compartment in a point-5-, address to the Section Removal and installation of the lower cover of a motive compartment.

8 Turn off bolts of fastening-1-and remove a forward peak of an arch of a wheel-2-.

Turn out an additional bolt in forward part from below. On an illustration the bolt is not visible.

9 Turn off fastening bolts-4 loker of a wing-3-. Take out clips-5-, thus at first take out pins, and then clips.

10 Open a door and through a crack turn off a fastening bolt (the shooter on an illustration) on a rack - And-.

11 Turn out three self-tapping screws 22 mm long-3-and one self-tapping screw 19 mm long-4-.

12 Turn out the top screws of fastening of Torx-2 of a wing-1-. 5 – nuts from sheet material.
13 Thanks to existence of a sheeting of the bottom the wing is reliably fixed. The hair dryer creating temperature not less than 400 °C is necessary for a detachment of a wing.
14 Install the hair dryer with a flat nozzle in the top and back region of a wing and soften a sheeting. After that remove from below in forward part of a prileganiye of a wing a sheeting. It is important to make it in the specified place, otherwise at removal the wing can vspuchitsya.
15 Remove a wing.


 REMOVAL

16 Clear adjacent surfaces of a wing, if necessary will correct.
17 If necessary coat a wing.
18 V places of a prileganiye lay a usual sealing tape.
19 Establish a wing into place, will expose approximately and slightly fix bolts.
20 Will expose a wing, thus watch a uniform gap in relation to a door and a cowl, address to Specifications.
21 Tighten all bolts of fastening of a wing.
22 Apply a sheeting on an internal surface of a wing.
23 Fix bolts a loker of a wing and a forward peak of an arch of a wheel. Insert clips and press aflush pins.
24 Establish into place a forward wheel so that the markings put at removal coincided. Previously grease with a thin layer of bearing greasing the aligning wheel disk belt on a nave. Do not grease bolts of fastening of a wheel. Replace rusty bolts. Wrap bolts. Lower the car on wheels and tighten bolts cross-wise the moment of 100 N • m.
25 Put on from above an element of protection of edges.
26 Establish a headlight, address to the Section Removal and installation of a headlight.
27 Install the lateral repeater of turn, address to the Section Replacement of Glow Lamps of External Lighting.
28 Put on a level a wing.