BMW 3 of the E46 series

1 Disconnect a reception pipe from a final collector, address to the Section Removal and installation of the inlet pipeline.
2 Turn off two bolts of fastening of the pipeline for air supply in a final collector.
3 Turn off bolts of fastening and remove a final collector from a head of cylinders.

4 Clear sealing surfaces on a final collector and a head of cylinders. Surely replace sealing laying with the new.
5 Grease a carving of hairpins of fastening of a final collector with high-temperature copper greasing.
6 Fix a final collector the new self-stopped copper nuts, having tightened them cross-wise from within outside, the efforts given in Specifications.
7 Fix the air supply pipeline with new laying on a final collector.
8 Fix a reception pipe with new consolidation the moment of 30 N • m on a final collector.

9 Remove the filtering element of the air filter of the engine, address to the Section Replacement of the Filtering Element of the Air Filter.

10 Uncover bolts of fastening of a turbocompressor in points-1-. 11 Remove the screen at a level-2-down (an arrow on an illustration).

12 Turn off bolts of fastening of a turbocompressor to a final collector through three openings.
13 Turn off two bolts of fastening of the pipeline of recirculation of the fulfilled gases from a final collector.
14 Turn off nuts of fastening and remove a final collector from a head of cylinders.

15 Clear sealing surfaces on a final collector and a head of cylinders. Surely replace sealing laying with the new.
16 Grease a carving of hairpins of fastening of a final collector with high-temperature copper greasing.
17 Fix a final collector the new self-stopped copper nuts, having tightened them cross-wise from within outside, the efforts given in Specifications.
18 Fix the pipeline for air supply with new laying on a final collector.
19 Fix a turbocompressor with new laying the moment of 45 N • m to a final collector.

20 Insert sideways to a level-2 screen.

21 Put to the place of a cover of bolts of fastening of a turbocompressor to the case of the air filter.
22 Establish the filtering element of the air filter of the engine, address to the Section Replacement of the Filtering Element of the Air Filter.

23 Remove an aircombined box, address to the Section Removal and installation of a box of an air inlet.
24 Remove oxygen sensors from both final collectors, address to the Section Removal and installation of the sensor of oxygen.
25 Turn off nuts of fastening and remove a reception pipe from a final collector, address to the Section Removal and installation of system of release.

26 Raise the engine the crane for a forward eye. If the crane available is not present, pass a cable through an eye. Enter a strong pipe under a cable and put it on two support.

Install the BMW 00 0 200 adaptation at the left and on the right on support of wings and fix them bolts. There is also other adaptation: No. KL-0205-3US KLANN.

27 Raise the engine the elevator approximately on 5 mm to unload engine support.
28 Remove the amplifier of forward part of the car, address to the Section Removal and installation of a beam of a forward suspension bracket.
29 Turn off bolts of fastening of the right support of the engine with an arm from a body and the engine.
30 Disconnect at first a forward, and then back final collector from a head of cylinders.

31 Clear sealing surfaces on a final collector and a head of cylinders. Surely replace sealing laying with the new.
32 Grease a carving of hairpins of fastening of a final collector with high-temperature copper greasing.
33 Fix a final collector the new self-stopped copper nuts, having tightened them cross-wise from within outside, the efforts given in Specifications.
34 Fix a reception pipe with new consolidation the moment of 30 N • m on a final collector.
35 Fix the right support of the engine and an arm, the efforts given in Specifications. Lower the engine, remove the crane.
36 Establish the amplifier of forward part of the car, address to the Section Removal and installation of a beam of a forward suspension bracket.
37 Install oxygen sensors on both final collectors, address to the Section Removal and installation of the sensor of oxygen.
38 Establish an aircombined box, address to the Section Removal and installation of a box of an air inlet.
39 Fix the lower cover of a motive compartment, address to the Section Removal and installation of the lower cover of a motive compartment.